黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

YC12VC型高速柴油机发火顺序的分析研究

基于AVL-EXCITE软件搭建了YC12VC发电用高速柴油机轴系动力学模型,其模拟值与试验值吻合性较好,验证了该模型可以较好地模拟不同工况条件下轴系的运动情况。基于平衡性和均匀发火等原则,设计了8种不同的发火顺序,并针对轴承受力、轴承润滑、轴系扭振和转速不均匀性开展影响规律研究。结果表明:通过发火顺序的优化,在保证最大主轴承负荷和最小油膜厚度满足设计要求的前提下,标定工况下的曲轴扭振总振幅从0.465°降低到0.259°,转速不均匀系数从0.018降低到0.009。     

Integral barrier Lyapunov function-based adaptive fuzzy output feedback control for nonlinear delayed systems with time-varying full-state constraints

In this article, an adaptive fuzzy output feedback control method is presented for nonlinear time-delay systems with time-varying full state constraints and input saturation. To overcome the problem of time-varying constraints, the integral barrier Lyapunov functions (IBLFs) integrating with dynamic surface control (DSC) are applied for the first time to keep the state from violating constraints. The effects of unknown time delays can be removed by using designed Lyapunov-Krasovskii functions (LKFs). An auxiliary design system is introduced to solve the problem of input saturation. The unknown nonlinear functions are approximated by the fuzzy logic systems (FLS), and the unmeasured states are estimated by a designed fuzzy observer. The novel controller can guarantee that all signals remain semiglobally uniformly ultimately bounded and satisfactory tracking performance is achieved. Finally, two simulation examples illustrate the effectiveness of the presented control methods.     

强化研磨加工中喷射角度对GCr15轴承钢板塑性变形的影响

利用ABAQUS有限元仿真软件研究不同喷射角度强化研磨加工GCr15轴承钢板过程的塑性变形,得到不同喷射角度与等效塑性应变沿真实路径距离的关系,并通过拉伸试验进行验证。喷射角度为90°的强化研磨加工伸长率为1.4%,相比未经过强化研磨加工的伸长率数值缩减了2.0%。断口收缩率由空白组的4.9%降低到喷射角为90°的2.2%。结合仿真和试验可知,强化研磨加工中喷射角度越大,塑性变形能力越低,材料加工越难。     

基于双应力加速寿命试验的关节轴承寿命预测与可靠性分析

自润滑关节轴承寿命主要是由衬垫的磨损性能决定的,但衬垫的磨损一般是非线性的,使得寿命难以预测。采用同时改变载荷和摆频2种应力的方法进行加速寿命试验,建立以pv值、磨损量退化数据为输入参数,寿命值为输出参数的灰色神经网络预测模型。经验证该预测模型对关节轴承寿命预测的最大误差仅为7.33%,平均误差仅为3.892%。对不同加速应力下自润滑关节轴承可靠性进行评估,结果表明,关节轴承的可靠性在L_(10)(可靠度为90%时的寿命)之前下降趋势缓慢,然后迅速下降,pv值越大可靠性下降越迅速;随着pv值的增大,关节轴承寿命近似呈指数下降,经验证可用逆幂率加速模型反映二者关系。     

Cutter mark cross method for improvement of contact stiffness by controlling distribution of real contact area

Contact surfaces do not make contact perfectly because such surfaces have a lot of asperities. The real contact area is much smaller than the nominal contact area, and the real contact areas has a non-uniform distribution because of the waviness in the contact surface. The contact stiffness is influenced not only by the deformation of the asperities, but also by the distribution of the real contact areas. In general, a contact surface with a uniform distribution of the real contact areas has greater contact stiffness. However, this requires a grinding finish and costs more than the cutting finish. In this study, a method for uniformly distributing the real contact areas easily, is proposed to improve the contact stiffness of a contact surface finished by cutting. The method is called the cutter mark cross (CMC) method. The allowable waviness in the CMC method is shown. In addition, the effect of the CMC method is investigated by experimentation. The results show that the real contact areas can be distributed uniformly using the CMC method. The horizontal and vertical contact stiffness can also be improved.     

A stiffness parameter and truncation error criterion for adaptive path following in structural mechanics

We explore a truncation error criterion to steer adaptive step length refinement and coarsening in incremental-iterative path following procedures, applied to problems in large-deformation structural mechanics. Elaborating on ideas proposed by Bergan and collaborators in the 1970s, we first describe an easily computable scalar stiffness parameter whose sign and rate of change provide reliable information on the local behavior and complexity of the equilibrium path. We then derive a simple scaling law that adaptively adjusts the length of the next step based on the rate of change of the stiffness parameter at previous points on the path. We show that this scaling is equivalent to keeping a local truncation error constant in each step. We demonstrate with numerical examples that our adaptive method follows a path with a significantly reduced number of points compared to an analysis with uniform step length of the same fidelity level. A comparison with Abaqus illustrates that the truncation error criterion effectively concentrates points around the smallest-scale features of the path, which is generally not possible with automatic incrementation solely based on local convergence properties.     

基于EEMD能量熵和混合算法的电机轴承故障诊断

针对提升机电机轴承振动信号的非平稳特性和单一粒子群算法(PSO) 优化径向基函数（RBF）神经网络时存在网络收敛速度慢和适应度值易陷入局部最小的缺点，提出基于集合经验模态分解（EEMD）能量熵和模拟退火粒子群混合算法（SAPSO）优化RBF神经网络的提升机电机轴承故障诊断方法。基于EEMD求取振动信号各固有模态函数分量的能量熵，并使用相关性分析方法剔除虚假的分量，把筛选后的有效数据作为故障识别的特征向量；利用模拟退火（SA）算法具有局部概率突跳的特性，将SA算法和PSO算法相结合，在优化RBF诊断模型隐含层参数时以实现不同算法间的优劣互补。仿真结果表明，使用SAPSO算法优化后的RBF神经网络模型在提升机电机轴承故障诊断中能够加快网络收敛速度和提升故障识别精度。     

基于MED和边际谱的自动倾斜器轴承故障诊断

针对直升机自动倾斜器轴承早期微弱故障特征易被强烈背景噪声淹没的问题，提出了一种基于最小熵反褶积（Minimum Entropy Deconvolution，MED）和边际谱的自动倾斜器轴承故障诊断方法。采用MED对采集的振动信号进行滤波降噪，提高了信号的信噪比，突出了轴承早期微弱故障特征；通过Hilbert变换和经验模态分解（Empirical Mode Decomposition，EMD）获取去噪包络信号的本征模态函数（Intrinsic Mode Functions，IMF）集，并引入峭度筛选准则选取合理IMF集计算局部Hilbert边际谱，有效地提取了故障特征频率，能够通过故障特征频率进行故障类型判别。通过某型直升机自动倾斜器故障诊断试验系统验证了该诊断方法的合理性和可行性。